South African Class 6E1, Series 10

6,972 mm (22 ft 10+12 in)Length:
​ • Over couplers15,494 mm (50 ft 10 in) • Over body14,631 mm (48 ft 0 in)Width2,896 mm (9 ft 6 in)Height:
​ • Pantograph4,089 mm (13 ft 5 in) • Body height3,937 mm (12 ft 11 in)Axle load22,447 kg (49,487 lb)Adhesive weight89,788 kg (197,949 lb)Loco weight89,788 kg (197,949 lb)Electric system/s3 kV DC catenaryCurrent pickup(s)PantographsTraction motorsFour AEI-283AY ​ • Rating 1 hour623 kW (835 hp) • Continuous563 kW (755 hp)Gear ratio18:67Loco brakeAir & RegenerativeTrain brakesAir & VacuumCouplersAAR knuckle
Performance figures
Maximum speed113 km/h (70 mph)
Power output:
 • 1 hour2,492 kW (3,342 hp)
 • Continuous2,252 kW (3,020 hp)
Tractive effort:
 • Starting311 kN (70,000 lbf)
 • 1 hour221 kN (50,000 lbf)
 • Continuous193 kN (43,000 lbf) @ 40 km/h (25 mph)
Career
OperatorsSouth African Railways
Spoornet
ClassClass 6E1
Number in class55
NumbersE2086-E2140
Delivered1982-1984
First run1982
Last run2005

The South African Railways Class 6E1, Series 10 of 1982 was an electric locomotive.

Between 1982 and 1984, the South African Railways placed 55 Class 6E1, Series 10 electric locomotives with a Bo-Bo wheel arrangement in service.[1]

Manufacturer

The 3 kV DC Class 6E1, Series 10 electric locomotive was designed and built for the South African Railways (SAR) by Union Carriage & Wagon (UCW) in Nigel, Transvaal. The electrical equipment was supplied by the General Electric Company (GEC).[2]

Between 1982 and 1984, 55 locomotives were delivered, numbered in the range from E2086 to E2140. Like Series 6 to 9, the Series 10 units were equipped with AEI-283AY traction motors. UCW did not allocate builder's numbers to the locomotives it built for the SAR, but used the SAR unit numbers for their record keeping.[1]

Characteristics

Orientation

These dual cab locomotives had a roof access ladder on one side only, just to the right of the cab access door. The roof access ladder end was marked as the no. 2 end. A corridor along the centre of the locomotive connected the cabs which were identical apart from the fact that the handbrake was located in cab 2. A pantograph hook stick was stowed in a tube, mounted below the lower edge of the locomotive body on the roof access ladder side. The locomotive had one square and two rectangular access panels along the lower half of the body and a large hatch door below the second small window to the right of the side door on the roof access ladder side, and only one square access panel and a large hatch door below the first window immediately to the right of the door on the opposite side.[1]

Series identifying features

The Class 6E1 was produced in eleven series over a period of nearly sixteen years. While some of the Class 6E1 series are visually indistinguishable from their predecessors or successors, some externally visible changes did occur over the years.[1]

Drainage holes on Series 9 to 11

Series 8 and later locomotives could be distinguished from all older models by the large hatch door on each side.[1][3]

The Series 9 to Series 11 locomotives were visually indistinguishable from each other, but could be distinguished from all earlier models by the rainwater drainage holes on their lower sides. These holes were usually covered by so-called buckets, but the covers were absent on a few locomotives. Another distinction was the end doors, which were recessed into the doorframes on Series 9 to Series 11 locomotives, compared to earlier models which had their end doors flush with the doorframes. In addition, on Series 9 and later, the split side window on the driver's assistant side was replaced by a single rectangular side window with rounded corners. Finally, unlike all earlier models, all four doors on Series 9 to Series 11 locomotives had rounded corners.[4]

Crew access

The Class 5E, 5E1, 6E and earlier 6E1 locomotives were notoriously difficult to enter from ground level, since their lever-style door handles were at waist level when standing inside the cab. This made it impossible to open the door from outside without first climbing up high enough to reach the door handle, while hanging on to the side handrails with one hand only. Crews therefore often chose to leave the doors ajar when parking and exiting the locomotives.[5]

Side doors with two interconnected latch handles on the outside, such as those which were introduced on the Class 7E1, with one outside handle mounted near floor level and the other at mid-door level, were also introduced on Class 6E1 locomotives beginning with Series 9.[6]

Service

The Class 6E1 family saw service all over both 3 kV DC mainline and branch line networks, the smaller Cape Western mainline between Cape Town and Beaufort West and the larger network which covers portions of the Northern Cape, the Free State, Natal, Gauteng, North West and Mpumalanga.[7]

Rebuilding to Class 18E

Cab 1 of Class 18E no. 18-108, ex Class 6E1 no. E2114, Capital Park, 1 October 2009

Beginning in 2000, Spoornet began a project to rebuild Series 2 to 11 Class 6E1 locomotives to Class 18E, Series 1 and Series 2 at the Transnet Rail Engineering (TRE) workshops at Koedoespoort. In the process, the cab at the no. 1 end was stripped of all controls and the driver's front and side windows were blanked off to have a toilet installed, thereby forfeiting the locomotive's bi-directional ability.[7][8]

Brake rack in Class 18E no. 18-089

Since the driving cab's noise level had to be below 85 decibels, cab 2 was selected as the Class 18E driving cab primarily based on its lower noise level compared to cab 1, which was closer and more exposed to the compressor's noise and vibration. Another factor was the closer proximity of cab 2 to the low voltage switch panel. The fact that the handbrake was located in cab 2 was not a deciding factor but was considered an additional benefit.[8]

While the earlier Class 6E1, Series 2 to 7 locomotives had been built with a brake system which consisted of various valves connected to each other with pipes, commonly referred to as a "bicycle frame" brake system, the Class 6E1, Series 8 to 11 locomotives were built with an air equipment frame brake system, commonly referred to as a brake rack. Since the design of the rebuilt Class 18E locomotives included the same brake rack, the rebuilding project was begun with the newer series 8 to 11 locomotives to reduce the overall cost of rebuilding.[8]

By June 2005 all Series 10 locomotives except numbers E2111 and E2134 were rebuilt to Class 18E, Series 1. The fate of the two exceptions is not known and they are presumed to have been scrapped. The numbers and renumbering details of the rebuilt units are listed in the table.[7][8]

Class 6E1, Series 10 units rebuilt to Class 18E

Count
6E1
no.
Year
built
18E
no.
18E
series
Year
rebuilt
Notes
1 E2086 1982 18-158 1 2004
2 E2087 1982 18-046 1 2002
3 E2088 1982 18-089 1 2003
4 E2089 1983 18-023 1 2002
5 E2090 1983 18-130 1 2004
6 E2091 1983 18-176 1 2004
7 E2092 1983 18-164 1 2005
8 E2093 1983 18-059 1 2002
9 E2094 1983 18-126 1 2004
10 E2095 1983 18-039 1 2002
11 E2096 1983 18-174 1 2004
12 E2097 1983 18-180 1 2005
13 E2098 1983 18-179 1 2005
14 E2099 1983 18-053 1 2002
15 E2100 1983 18-149 1 2004
16 E2101 1983 18-166 1 2003
17 E2102 1983 18-044 1 2002
18 E2103 1983 18-175 1 2004
19 E2104 1983 18-160 1 2005
20 E2105 1983 18-102 1 2003
21 E2106 1983 18-004 1 2001
22 E2107 1983 18-186 1 2005
23 E2108 1983 18-177 1 2004
24 E2109 1983 18-081 1 2003
25 E2110 1983 18-052 1 2002
26 E2112 1983 18-060 1 2002
27 E2113 1983 18-151 1 2004
28 E2114 1983 18-108 1 2004
29 E2115 1983 18-191 1 2005
30 E2116 1983 18-099 1 2003
31 E2117 1983 18-155 1 2004
32 E2118 1983 18-096 1 2003
33 E2119 1983 18-024 1 2002
34 E2120 1983 18-122 1 2004
35 E2121 1983 18-113 1 2004
36 E2122 1983 18-085 1 2003
37 E2123 1983 18-103 1 2003
38 E2124 1983 18-076 1 2003
39 E2125 1983 18-016 1 2002
40 E2126 1984 18-082 1 2003
41 E2127 1984 18-131 1 2004
42 E2128 1984 18-032 1 2002
43 E2129 1984 18-043 1 2002
44 E2130 1984 18-121 1 2004
45 E2131 1984 18-040 1 2002 to 18-862
46 E2132 1984 18-047 1 2002
47 E2133 1984 18-123 1 2004
48 E2135 1984 18-114 1 2004
49 E2136 1984 18-132 1 2004
50 E2137 1984 18-115 1 2004
51 E2138 1984 18-088 1 2003
52 E2139 1984 18-128 1 2004
53 E2140 1984 18-153 1 2004

Liveries

All the Class 6E1, Series 10 locomotives were delivered in the SAR red oxide livery with signal red cowcatchers, yellow whiskers and with the number plates on the sides mounted on three-stripe yellow wings. In the 1990s some of the Series 10 units were repainted in the Spoornet orange livery with a yellow and blue chevron pattern on the cowcatchers.[9]

References

  1. ^ a b c d e South African Railways Index and Diagrams Electric and Diesel Locomotives, 610mm and 1065mm Gauges, Ref LXD 14/1/100/20, 28 January 1975, as amended
  2. ^ "UCW - Electric locomotives" (PDF). The UCW Partnership. Archived from the original (PDF) on 12 October 2007. Retrieved 30 September 2010.
  3. ^ Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 128–129. ISBN 0869772112.
  4. ^ 18-050 (ex Series 9 E2013) with recessed end door and rounded door corners
  5. ^ E1882 with high mounted door handle
  6. ^ 18-253 (ex Series 9 E2058) with two door handles
  7. ^ a b c Railways of Southern Africa Locomotive Guide, 2002 Edition, (Compiled by John N. Middleton), p57, as amended by Combined Amendment List 4, January 2009
  8. ^ a b c d Information gathered from the rebuild files of individual locomotives at Transnet Rail Engineering's Koedoespoort shops, or obtained from John Middleton as well as several Transnet employees
  9. ^ Soul of A Railway, System 7, Western Transvaal, based in Johannesburg, Part 9. South-Eastwards as far as Volksrust (2nd part) by Les Pivnic. Caption 4. (Accessed on 11 April 2017)
  • v
  • t
  • e
Steam
7' ¼" gauge
Standard gauge
  • CGR 0-4-0ST Aid
  • Natal 0-4-0ST Durban
  • Natal 0-4-0WT Natal
  • Natal 4-4-0T Perseverance
Cape gauge
Tank engines
  • Durban's Congella
  • Durban's Edward Innes
  • Durban's John Milne
  • Durban's Sir Albert
Cape gauge
Tender engines
Cape gauge
Articulated
engines
2' 6" gauge
  • Cape Copper John King & Miner
  • Cape Copper Britannia
  • Cape Copper Caledonia
  • Cape Copper Clara
  • Cape Copper Condenser
  • Cape Copper Scotia
  • Namaqua Copper Pioneer
  • Walvis Bay 2-4-2T Hope
2' & 600mm
gauges
Electric
Gas-electricDiesel
Cape gauge
Diesel-electric
2' gauge
Diesel-electric
Cape gauge
Diesel-hydraulic
Cape gauge
Electro-diesel

External links

Media related to South African Class 6E1 Series 10 at Wikimedia Commons